What went wrong with your FX today?
- Thread starter Dracula
- Start date
Be careful where and who you're buying from... Lots of counterfeits.
New King is the osram cbh
3600lm
D2S: Osram Xenarc 66240 CBH - HID Headlight Bulbs from The Retrofit Source
Cbi is 3500lm
Sent from my S7E .. RIP N7.. ='(
- Car
- 2004 FX35 AWD
- Name
- John Green
Yes saw allot of counterfeits (made in China)on eBay but the ones I ordered were from Germany.
At 100.00ea the CBH's are a little steep at twice the cost.
You asked if the cbi's were the brightest... Nope not anymore... Cbh!
You didn't happen to ask the if the cost/value was worth it over the cbi's. [emoji12]
Sent from my S7E .. RIP N7.. ='(
illestFX35
Member
- Car
- 2010 FX35 RWD
Lowered my car more yesterday. Adjusted preload higher and stiffened up dampening. Im rubbing going up every driveway in the front. I broke some clips and a screw. Has anyone done fender work on 2nd gen and know exactly what I need to do? I want to widen my stance, but not happening until I do something with my fenders.
http://uploads. -cdn.com/20161101/b9f60e0ae20111fa70c1f14453053870.jpg
Sent from my iPhone
http://uploads. -cdn.com/20161101/b9f60e0ae20111fa70c1f14453053870.jpg
Sent from my iPhone
- Car
- 2004 FX35 AWD
- Name
- John Green
Yea turned out to be the plug on the ballast had come loose!
- Car
- 2017 QX70S
- Name
- Andy
@illestFX35, most likely you'll be the first to roll the 2nd Gen fender. I don't recall any 2nd Gen got this done.
- Car
- 2004 FX35 AWD
- Name
- John Green
P0442 Infiniti EVAP Control System Leak Detected Small Leak OBDII Engine Light Trouble Code | Engine-Codes.comGot a P0442 driving back from work
What should be the first thing I should check out ?
Make sure your gas cap is tight
- Car
- 2006 FX35 RWD
- Name
- Nnaji
Does the right side of the seal on this caliper piston look a bit off to any of you guys? When I was doing a brake pad bedding procedure, I smelled burning brake fluid only on this caliper and there were no leaks on the line and bleeder.. Looks like it came from the piston.
I mightve messed up when I pushed the piston back in with a spreader without opening the bleeder valve?
http://uploads. -cdn.com/20161102/9438c46a767f01212a8d93865369d5b1.jpg
http://uploads. -cdn.com/20161102/817c884bfb5c3e1cd84094a0bc950219.jpg
http://uploads. -cdn.com/20161102/09aae0598bb19b31a55108d335e883c5.jpg
http://uploads. -cdn.com/20161102/482c494a0e29a4012a52a692906e3cf5.jpg
I mightve messed up when I pushed the piston back in with a spreader without opening the bleeder valve?
http://uploads. -cdn.com/20161102/9438c46a767f01212a8d93865369d5b1.jpg
http://uploads. -cdn.com/20161102/817c884bfb5c3e1cd84094a0bc950219.jpg
http://uploads. -cdn.com/20161102/09aae0598bb19b31a55108d335e883c5.jpg
http://uploads. -cdn.com/20161102/482c494a0e29a4012a52a692906e3cf5.jpg
Driving home from work today, I could hear this loud rattling noise. Looked under my fx to check and saw nothing. As I pulled off I heard it again. So now I get out to do a 360° my custom nismo exhaust tips is barely holding on by the hair on its chinny chin chin. But it's so rusted it was just dragging. So now it looks as if I have a single exit exhaust. Fml
I never open the bleeder valve when I do this, I just do it very slowly and I never had issues. If it's not leaking I would say you're fine.
- Car
- 2006 FX35 RWD
- Name
- Nnaji
Oddly enough, I guess it is fine. One thing I noticed is one of the caliper pin coots had a tear in it, so I just replaced both boots on that caliper and all was well after disassembling and assembling it back?
ha there you go, it's not an issue :P
- Car
- 09 FX50
Problem with our fender setups is there really isnt a way to 'roll' them like on most cars. On the first gen I trimmed my inner fender and the bottom of the plastic molding to clear my GTR wheels + low eibach springs. Look at how the plastic attaches to the fender - can't really alter it too much without losing the ability to snap in the plastic molding.