What did you do to your FX / QX70 today?

Well, I went and pickup Jonas FX50S spare tire for a test fit onto my BBK setup. It no go. The spare rim is not wide (diameter wise) enough. I believe the spare is 18". I need at least 20" to clear the BBK.
 
la_fx35 said:
Well, I went and pickup Jonas FX50S spare tire for a test fit onto my BBK setup. It no go. The spare rim is not wide (diameter wise) enough. I believe the spare is 18". I need at least 20" to clear the BBK.
Click to expand...

Aw that sucks. I was really hoping it would work for you.
 
I just replaced the camshaft sensors on my 2005 FX35, I broken one of the connectors on (Bank 1) do any know where to find one?

---------- Post added at 09:54 AM ---------- Previous post was at 09:20 AM ----------

I had to put a tie strap to hold my camshaft connector in place, I need one bad!!

---------- Post added at 09:56 AM ---------- Previous post was at 09:54 AM ----------

My FX35 really runs great now with the new Cam sensor installed

---------- Post added at 09:58 AM ---------- Previous post was at 09:56 AM ----------

Do any one know how to make quick House power for my FX35?

---------- Post added at 10:00 AM ---------- Previous post was at 09:58 AM ----------

Do nay one know if theirs a bolt on Nitrous kit for the FX35?
 
So the past few days for me:

CameraZOOM-20130531142449515_zps38a82c09.jpg

Getting my new wheels on, above is stock, below is 10.5 GTR wheels with the Ventus ST RH06's

CameraZOOM-20130531144249975_zpsff2ea9b9.jpg

CameraZOOM-20130601145126170_zps0ab11731.jpg

Stance after the fact.

CameraZOOM-20130601164931285_zpsedf06e32.jpg

Good shot, of the Blackworks Racing Gold Lugs and my tires. I have since cleaned off the excess glue.

CameraZOOM-20130528200913402_zps58345f5f.jpg

My Panavise Cellphone mount

CameraZOOM-20130528200933330_zpsc37138ae.jpg

It is installed but I have no pictures of it in the car. Will grab some soon. I have to get out there with my DSLR.
 
:good: Good looking stance as always with the GTR wheels. I want to hear your feedback on the Panavise mount. I had one and it bounces pretty bad. May the +06 mount is different from the -06?
 
la_fx35 said:
:good: Good looking stance as always with the GTR wheels. I want to hear your feedback on the Panavise mount. I had one and it bounces pretty bad. May the +06 mount is different from the -06?
Click to expand...

Thanks, I moved the 25mm H&R's up front. Might end up swapping those out for a set of 30mm in the near future.

As for the panavise mount, I have no complaints, no bounce and even with a really cheap cell phone holder it still grips good. I know there is differences in the -06 and +06. I only affixed one of the three screws as well, they sent two extra screws to affix it and I never used them. It seems that the actual dash and center console area pinch the mount so tight that it cannot really move much anyways.

For me it was between the Kuda mount and the Panavise, I ended up with the panavise cause it was about $50 cheaper and i felt where the phone ended up being positioned is better (its illegal to use your phone while driving in canada but with the mount if kinda just looks like I am using the navigation or something).
 
Dipped the door handles this past weekend. From far away it looks alright but close up it's a bit too textured for me. I'm gonna get the door handles and chrome trim at the bottom of the doors color matched and painted soon.

[Dead Link Removed]
 
Last edited by a moderator:
PDXSchrammie said:
Dipped the door handles this past weekend. From far away it looks alright but close up it's a bit too textured for me. I'm gonna get the door handles and chrome trim at the bottom of the doors color matched and painted soon.

View attachment 206062
Click to expand...

I love your colour. I kinda like the chrom that kinda adds some pop with your wheels, but im sure once I see it colour matched it will look good too.

Here are the last couple of things I managed to do before I left the FX again for three weeks:

IMG_0857_zps40a950b0.jpg

Blackworks Racing Fender Washer Kit, matches my Lug nuts and will eventually match my fittings and wires in the engine bay as I am going to rewire almost everything under there. I still have a lot of cleaning and work to do in the engine bay, biggest thing is the Kinetix V+ plenum I am sourcing.

And here are the two pictures of the Panavise mount (for andy):

IMG_0856_zpse3faa730.jpg

IMG_0854_zpsf8a47f2f.jpg

(I am re-wrapping that clock area, I just ran out of material).
 
Meme405, nice wheels . Some of you guys have way too much money, i wish I could spend like most of you here but dang my wife notices everything lol! For now, clear plasti dipped the chrome accents all around. Looks brushed aluminum now.. Next, trunk to pick up a set of Ake's
 
You must log in or register to reply here.
Back
Top