I'm working on getting coilovers but don't want to deal with uneven tire wear and bad alignment. My current setup produces no uneven wear even if it's a little out of spec in some readings with H&R Lowering Springs.
I need a best guess on how low I can go, if any, in comparison to my H&R setup. I read that Turbo said the fronts can go very low and with the camber plate anyway, that's not an issue.
So what I'm most concerned about are the rears. Is there anyway someone can guestimate how much lower I can go with coilovers vs my H&R's? 1 inch? .5 inch? Not any farther?
Trying to eliminating having to adjust the height setting too much and pay a lot of money on getting alignments done. If no one has any suggestions, I might just have to leave the rears the same height as the H&R's.
Also, if I'm going around 60 mph or higher, my car is slightly pulling to the right. Is that the "Front Total Steer Ahead" I need to ask them to play with?
Alignment Numbers
Actual = (Before, Current):
Left Front Camber
Spec: 0.0 to -1.5
Actual = -1.2, -1.2
Left Front Caster
Spec: 4.5 to 3.0
Actual = 3.8, 3.8
Left Front Toe
Spec: .02 to .1
Actual = .12 (OUT OF SPEC), .07
Right Front Camber
Spec: -1.5 to 0
Actual = -1.2, -1.1
Right Front Caster
Spec: 3.0 to 4.5
Actual = 3.6, 3.6
Right Front Toe
Spec: .1 to .02
Actual = .03, .07
Front Total Toe
Spec: .05 to .21
Actual = .14, .14
Front Total Steer Ahead
Spec: -.05 to .05
Actual = .04, .0
Left Rear Camber
Spec: -.3 to -1.3
Actual = -1.6 (OUT OF SPEC), -1.4 (OUT OF SPEC)
Left Rear Toe
Spec: .09 to .28
Actual = .17, .15
Right Rear Camber
Spec: -1.3 to -.3
Actual = -1.5 (OUT OF SPEC), -1.3
Right Rear Toe
Spec: .28 to .09
Actual = .14, .19
Rear Total Toe
Spec: .19 to .55
Actual = .31, .33
Rear Trust Angle
Spec: (no spec)
Actual = .02, -.02
I need a best guess on how low I can go, if any, in comparison to my H&R setup. I read that Turbo said the fronts can go very low and with the camber plate anyway, that's not an issue.
So what I'm most concerned about are the rears. Is there anyway someone can guestimate how much lower I can go with coilovers vs my H&R's? 1 inch? .5 inch? Not any farther?
Trying to eliminating having to adjust the height setting too much and pay a lot of money on getting alignments done. If no one has any suggestions, I might just have to leave the rears the same height as the H&R's.
Also, if I'm going around 60 mph or higher, my car is slightly pulling to the right. Is that the "Front Total Steer Ahead" I need to ask them to play with?
Alignment Numbers
Actual = (Before, Current):
Left Front Camber
Spec: 0.0 to -1.5
Actual = -1.2, -1.2
Left Front Caster
Spec: 4.5 to 3.0
Actual = 3.8, 3.8
Left Front Toe
Spec: .02 to .1
Actual = .12 (OUT OF SPEC), .07
Right Front Camber
Spec: -1.5 to 0
Actual = -1.2, -1.1
Right Front Caster
Spec: 3.0 to 4.5
Actual = 3.6, 3.6
Right Front Toe
Spec: .1 to .02
Actual = .03, .07
Front Total Toe
Spec: .05 to .21
Actual = .14, .14
Front Total Steer Ahead
Spec: -.05 to .05
Actual = .04, .0
Left Rear Camber
Spec: -.3 to -1.3
Actual = -1.6 (OUT OF SPEC), -1.4 (OUT OF SPEC)
Left Rear Toe
Spec: .09 to .28
Actual = .17, .15
Right Rear Camber
Spec: -1.3 to -.3
Actual = -1.5 (OUT OF SPEC), -1.3
Right Rear Toe
Spec: .28 to .09
Actual = .14, .19
Rear Total Toe
Spec: .19 to .55
Actual = .31, .33
Rear Trust Angle
Spec: (no spec)
Actual = .02, -.02