3M DINOC Interior Wrap Beginning to End
- Thread starter david
- Start date
Koso Kustomz
Member
- Location
- Idaho
That looks really good!
- Location
- Miami
- Car
- 2004 Infiniti FX35 Supercharged
I tried it once, didn't came out as good as I thought(if you are aiming for a wet carbon look).
mbarb15
Member
- Location
- Lyndhurst, NJ
not really aiming for the wet carbon look but more of an extra protectant to the vinyl.. i may go for an oem brushed alum look to cover up the scratches that the prev owner put on it
- Location
- Miami
- Car
- 2004 Infiniti FX35 Supercharged
Then yes it will work, you can easily put CC on top of vinyl.
mbarb15
Member
- Location
- Lyndhurst, NJ
ty.. i may give it a shot.. if i can find a used console bezel replacement in good condition ill take that over a new one at 250 ish
Slamming45
Member
- Location
- Illinois
- Car
- 1965 mustang
Personally I would not try this, the surface is to slick for the CC to adhere properly. Just my .02
---------- Post added at 03:15 PM ---------- Previous post was at 03:13 PM ----------
The Vinyl is cheap enough to re-apply if it becomes scratched or damaged.
---------- Post added at 03:15 PM ---------- Previous post was at 03:13 PM ----------
The Vinyl is cheap enough to re-apply if it becomes scratched or damaged.
mbarb15
Member
- Location
- Lyndhurst, NJ
Hmm, u could be right, not sure.. I may just spend the extra money n replace the trim
Slamming45
Member
- Location
- Illinois
- Car
- 1965 mustang
Replace, much better idea. You will then have more to play around with to wrap say a phone, laptop, I even did a bic...
Nebz
Member
- Location
- Orlando, FL
Anyone ever try a chrome finish wrap in the interior?
jmanhas
Member
- Location
- Vancouver, B.C.
is there an online DIY on how to disassemble the interior pieces? This is something I'm definitely looking to do on mine.
My shifter stack area is full of scratches and some dents..the CF vinyl would make it look 100 times better!
My shifter stack area is full of scratches and some dents..the CF vinyl would make it look 100 times better!
Nothing fully official, but you can follow this link with written step by step info on removing the trim pieces.
It's really easy. If you have the service manual you can also check there
https://www.infinitiscene.com/searc...this-CF-interior-dash-kit?p=274099#post274099
jmanhas
Member
- Location
- Vancouver, B.C.
sweet! I really appreciate it your post. I've been trying to find a set of instructions for the longest time. I'll probably need to order a set of these tools.
jmanhas
Member
- Location
- Vancouver, B.C.
one of the best mods yet to hide those ugly dents lol
STIBungy
Member
- Location
- Denver, CO
- Car
- 2007 FX35 AWD
I have a bunch of those on mine as well. The previous owner must be nuts because there are gouges on there. I might have to bondo some areas to smoothen it out before covering it.
vancity
Member
- Location
- Vancouver, BC, Canada
Looking to do mine as well.. im in Vancouver too I got a frickn dent so annoying!
---------- Post added at 01:34 PM ---------- Previous post was at 01:32 PM ----------
same. prev owner manage to get a dent by the shifter.. wtf how is that possible u gotta have a set of keys weighing 40 lbs to push it in like that.. not sure if wrap will even suffice.
should I take a pic for suggestions?
jtharness
Member
Approximately how many square feet did you need in order to do all of the interior pieces? Was looking into this mod as well and could definitely use some insight. Thanks
- Location
- Vancouver, BC
- Car
- 2008 FX35
to do all the interior pieces about 4 square feet. if you plan to make it perfect, or havnt wrapped before buy 6 square feet to be safe.
Note: This is if you want to do all the silver pieces including the door handles, steering wheel covers, and the center console area.
Note: This is if you want to do all the silver pieces including the door handles, steering wheel covers, and the center console area.
jtharness
Member
^Awesome. Thanks for the intel. I will order 6sq feet just to play it safe. Much appreciated.