UR crank pulley for 08 FX35
- Thread starter an959
- Start date
- Location
- Portland, OR
I think jbaker1121 used to have that pulley installed...
- Location
- Westchester, New York
- Car
- 09 FX50
yessir! I loved it
bump for 07-08 FX35er with UR pulley
Im pretty confident that the 03-08 pulleys are all the same size, as long as you get the stock-sized lightweight pulley you should be fine.
I think the reason it only lists 03-05 is because that's when they made them, before the 06-08 were 'different'.
You can always call and double-check. They are actually in NY on long island, I ordered my pulley from their shop as a walk-in. You can always go there in person and have them do measurements to make sure it's the same. They were really helpful when I went.
Good luck!
I have the lighweight stock size on my 06....it should fit the same. Same exact
engine as 07/08 so shouldn't be any issues...
fx55
Member
- Location
- Northern Jersey
an959, do you know if the UR pulley is the same as the 07?
- Location
- Westchester, New York
- Car
- 09 FX50
Pulley makes it feel like the revs climb higher but overall it doesn't do much actual power-wise....I had the UR pulley on my 05 fx...waste of money and install price IMO
- Location
- Westchester, New York
- Car
- 09 FX50
Neither does much at all...even with a tune. Stop wasting money on bolt-ons
fx55
Member
- Location
- Northern Jersey
JB,
It’ll be my third time changing the belt out in less than 1.5 years and my stock pulley is all rusted out. So I was thinking that’s the main reason why I haven’t getting the pull when I hit the gas. I know the UR pulley was one of your many mods on you old ride. With that taken into consideration, you wouldn’t recommend me getting the UR pulley even though I’ve got to replace the old stock pulley?
It’ll be my third time changing the belt out in less than 1.5 years and my stock pulley is all rusted out. So I was thinking that’s the main reason why I haven’t getting the pull when I hit the gas. I know the UR pulley was one of your many mods on you old ride. With that taken into consideration, you wouldn’t recommend me getting the UR pulley even though I’ve got to replace the old stock pulley?
- Location
- Westchester, New York
- Car
- 09 FX50
If you absolutely need to replace the pulley then I would say go for it, because they are prob around the same price. Labor is what kills it.
fx55
Member
- Location
- Northern Jersey
Thanks for the heads up. By any chance did you come across any problems when you had the UR pulley?
- Location
- Westchester, New York
- Car
- 09 FX50
no problems at all....just that it didn't do much haha
In post#5 above you said you loved the UR pulley, what happened over the last eight months to change your mind?
- Location
- Westchester, New York
- Car
- 09 FX50
Well I did love it for what it was, but I don't recommend people getting an aftermarket pulley in general no that we're on the topic of buying bolt ons etc in other threads.... unless you need it or are dying for another mod...the install costs outwieghs the cost benefit of buying it in the first place....
fx55
Member
- Location
- Northern Jersey
Still confused about the UR crank pulley (stock diameter)Part id: 021011512. Can someone confirm if it will fit a 2007 FX35 AWD please?I’ve reached out to several venders trying to confirm before placing the orderbut none of them every got back to me.
fx55
Member
- Location
- Northern Jersey
JB... Gotta give it to you. After going crazy trying to locate the UR pulley for my 07, I ended up contacting Vinny. Long story short.. He also recommended if I’m not going FI and if it’s absolutely in need to be swapped out then go OEM.