IS Wheel Studio (COMPS ONLY)
- Thread starter gto
- Start date
playing with ps trying to get an idea what a few different wheels might look like on my fx... trying to decide on an iforged & see different ones on it... it's a real pain trying to get it to look good enough to see what it'l look like in ps, but it really helps picture what it'll look like...
the yellow calipers with the black look SICK
P
Psiclne
Guest
Hey John the first set ^^^^^^ looks hot
ah, something about the aero's just don't do it for me, maybe because there pretty common or maybe it's cause I almost scored a used set for pretty cheap & now hate to pay full boat for something I felt I coulda gotten cheaper, dunno, but the aero's are not for me...
I like the evolution's & the variant's I think the most, but the daytonas are also pretty cool, my first choice was the vip triumph, but looking at them on the fx in ps I think maybe too many spokes... ah, tough decision...
I like the evolution's & the variant's I think the most, but the daytonas are also pretty cool, my first choice was the vip triumph, but looking at them on the fx in ps I think maybe too many spokes... ah, tough decision...
Where did you see that? The one in this thread is Berylium..
just ordered the variants like this:
the lips will be a bit different with more lip in the rear, waiting to see what iforged projects as actual lip size but I requested that the front be 2-3" smaller than the rear, plus, I didn't bother in that ps to make all the ss bolts all shiny, but they will be & everything else semi-gloss black. with this particular wheel design I wasn't feeling the centers body color with the semigloss lips only, so complete semigloss it is
final calculations came to 22x11 out back with +48 offset & 22x9.5 front with +32 offset... now I just gotta hope it fits the rear will be about as stuffed as I think possible with a 315/30 tire out back, inner will have minimal clearance & outer may need a rolled lip...oh boy do I hope it fits fronts will be 265/35's... pretty staggered with the fronts being at least 1.5" narrower than the rear...
worse case is it should come down to the posibility of the rears being off a mm or 2 or 3 to close inside, rather error to the inside & then if I screwed up, worse case a minimal spacer, although from all of my measurements I think it will fit just right... I hope.... fingers crossed...
the lips will be a bit different with more lip in the rear, waiting to see what iforged projects as actual lip size but I requested that the front be 2-3" smaller than the rear, plus, I didn't bother in that ps to make all the ss bolts all shiny, but they will be & everything else semi-gloss black. with this particular wheel design I wasn't feeling the centers body color with the semigloss lips only, so complete semigloss it is
final calculations came to 22x11 out back with +48 offset & 22x9.5 front with +32 offset... now I just gotta hope it fits
the rear will be about as stuffed as I think possible with a 315/30 tire out back, inner will have minimal clearance & outer may need a rolled lip...oh boy do I hope it fits fronts will be 265/35's... pretty staggered with the fronts being at least 1.5" narrower than the rear...worse case is it should come down to the posibility of the rears being off a mm or 2 or 3 to close inside, rather error to the inside & then if I screwed up, worse case a minimal spacer, although from all of my measurements I think it will fit just right... I hope.... fingers crossed...
Last edited:
nervous? maybe a little :err: but no matter what I'll get them on there I think...
also, with the visual it's kinda hard to see what these'll really look like cause the ones that I ps'd from might have been like 18's-19's or so, so in stretching them to 22's it made the whole center bolt area bigger than it should be & the actual bars wil be a slight bit less beefy than they look in that shot & will be a little longer looking & narrower than what's shown in my mockup... might try & do a more acurate comp to see what it will really look like in 22's & add the bright lugs, bolts & center cap, but at this point there ordered anyway sooo.... like I said, fingers crossed
also, with the visual it's kinda hard to see what these'll really look like cause the ones that I ps'd from might have been like 18's-19's or so, so in stretching them to 22's it made the whole center bolt area bigger than it should be & the actual bars wil be a slight bit less beefy than they look in that shot & will be a little longer looking & narrower than what's shown in my mockup... might try & do a more acurate comp to see what it will really look like in 22's & add the bright lugs, bolts & center cap, but at this point there ordered anyway sooo.... like I said, fingers crossed