i need to get those 21" rims, i wnt them so bad
purchased new June 2006 with 10miles
Motodyne copper thermal 5/16 spacer
Cypher +2 Advanced Timing
Stillen z-tube intake
K&N drop in filter
Oil reservoir catch filter (de-installed)
"turbocad6" FX50s Paddle Shifters
Tonneau trunk cover add-on
WeatherTech front mats
Front Window Tints 35%
OEM gen2 FX cargo organizer
B-Quiet Ultimate sound deaden (all over, doors/rear seats/trunk)
"turbocad6" 06+ badgeless gloss black custom grille
"turbocad6" Benz S550 side mirror LED
"turbocad6" Blacked out headlights w/ chrome rings & translucent vinyl corners
Infiniti OEM FX50s 21" Enkei
Bridgestone Dueler H/L 400 All Season 265/45/21
Infiniti OEM FX50s BBK F/R & "turbocad6" ball joints
StopTech SS brake lines: front & rear
Ichiba V1 15mm wheel spacers: front & rear
OEM Shanked wheel locks
H&R Lowered Sport Springs
GTspec front STB
GTspec front lower
GTspec front ladder
GTspec rear tie
GTspec rear lateral
iKey integrated remote starter / alarm
OEM Nissan iPod gateway : front harness
HID H8 3000k fogs
Nav/GPS bypass switch
i need to get those 21" rims, i wnt them so bad
Such a tight ride.....Anything with TC6 parts on it has to be above and beyond =) "Grocery getter", love the name.....
Nice ride, what if any performance and sound difference did the spacer give you?
clean as always Soon.
I take it you're referring to the Motodyne Plenum spacer, it's the best bang for the buck. Performance is def there and many forum members can confirm. Sound wise seems the same to me, then again I usually drive like a granny. I have no regrets on the plenum mod, it also ties in well with a better intake system.
---------- Post added at 12:11 PM ---------- Previous post was at 12:10 PM ----------
thanks sujit, how your FX treating you (last I heard, u still driving it)?
Hey Soonster. Was wondering what you used to overlay the reflectors in your headlight?
Thanks for the vinyl tip... I need to remember that when I paint the headlights in the future.
Rooted Samsung Galaxy S2 on TapaTalk
You say you have a cargo organizer. Do you have sub or magic box in the cargo area?
Wow that's slick. I like that.
i should have gotten this cargo organizer instead of the first generation organizer.
Spent 4hrs preparing / applying "b-quiet ultimate" damping material to the front passenger door. Added a good amount of weight and fingers are f@#$ked.
Noticed the door already have a few pieces of factory damping materials. On this first pic, the center small shiny square is what I started with:
Laid out more to cover the the bigger exposed areas.
Reassembled and spread some more sheets. Big thanks to turbocad for the advices and help. Still got 3 more doors to go (should take less time now that I know the process) ....
![]()
Last edited by soonster; 01-29-2012 at 09:01 AM.
Very nice. When you close the door, do you get that nice, solid thump? Does it help isolate or muffle minor vibrations in the door panels too? Any plans do to the under the headliner? I've been thinking of doing this too.
1. the sound of door closing seems the same, but the weight is definitely there
2. my muffler is OEM , didnt make any difference since it's only 1 door done at this point
3. no, wont be touching the headliner, that would be a huge job and would be nice
4. you should, since it'll pay in the longer run and cures the MOD bug![]()
Nice Soon, want to hear the full report when its all installed.
Just wondering if you felt any performance improvements with the z tube and stock box with a k&n drop in. Thinking about doing the whole stillen cai, z tube and plenum spacer. Just getting as much info on the results as i can.
I did the k&n flat filter and ztube first, performance was a slight improvement. Then ~1 yr after, done the motordyne install and 2+ advance timing and that was a huge noticeable difference. All the different mods ties in well and in low budget.
If I was in your shoes; DO ALL on your list ,reset the ECU and you'll have a nice smile.